Framing Math Cheat Sheet (Free Printable)
Updated
One page of the numbers framers look up most, free to print and tape inside the truck. Every value comes from the same math as our calculators; open a calculator for any size not listed.
Studs for a wall (layout studs)
| Wall length | 16" O.C. | 24" O.C. |
|---|---|---|
| 4' | 4 | 3 |
| 8' | 7 | 5 |
| 10' | 9 | 6 |
| 12' | 10 | 7 |
| 16' | 13 | 9 |
| 20' | 16 | 11 |
| 24' | 19 | 13 |
| 30' | 24 | 16 |
| 40' | 31 | 21 |
Studs on layout from end to end, plus one at the end. Add 2 per corner, tee and opening, then ~10% for culls.
Stairs: risers for a total rise
| Total rise | Risers | Riser height | Treads | Total run |
|---|---|---|---|---|
| 3'-0" | 5 | 7 3/16" | 4 | 3'-4" |
| 4'-0" | 7 | 6 7/8" | 6 | 5'-0" |
| 6'-0" | 10 | 7 3/16" | 9 | 7'-6" |
| 7'-0" | 11 | 7 5/8" | 10 | 8'-4" |
| 8'-0" | 13 | 7 3/8" | 12 | 10'-0" |
| 8'-6" | 14 | 7 5/16" | 13 | 10'-10" |
| 9'-0" | 14 | 7 11/16" | 13 | 10'-10" |
| 9'-6" | 15 | 7 5/8" | 14 | 11'-8" |
| 10'-0" | 16 | 7 1/2" | 15 | 12'-6" |
IRC R311.7.5: risers 7 3/4" max, treads 10" min. Total run at 10" treads.
Floor joist max span, No. 2 grade
| Size | DF-L 12" | DF-L 16" | DF-L 24" | SPF 12" | SPF 16" | SPF 24" |
|---|---|---|---|---|---|---|
| 2×6 | 10'-9" | 9'-9" | 8'-3" | 10'-3" | 9'-4" | 8'-1" |
| 2×8 | 14'-2" | 12'-9" | 10'-5" | 13'-6" | 12'-3" | 10'-3" |
| 2×10 | 18'-0" | 15'-7" | 12'-9" | 17'-3" | 15'-5" | 12'-7" |
| 2×12 | 20'-11" | 18'-1" | 14'-9" | 20'-7" | 17'-10" | 14'-7" |
IRC Table R502.3.1(2): living areas, 40 psf live + 10 psf dead load, L/360. Sleeping areas and other grades: use the calculator.
Roof pitch
| Pitch | Angle | Rafter factor | Rafter per ft of run |
|---|---|---|---|
| 3/12 | 14.04° | 1.031 | 1'-0 3/8" |
| 4/12 | 18.43° | 1.054 | 1'-0 5/8" |
| 5/12 | 22.62° | 1.083 | 1'-1" |
| 6/12 | 26.57° | 1.118 | 1'-1 7/16" |
| 7/12 | 30.26° | 1.158 | 1'-1 7/8" |
| 8/12 | 33.69° | 1.202 | 1'-2 7/16" |
| 9/12 | 36.87° | 1.250 | 1'-3" |
| 10/12 | 39.81° | 1.302 | 1'-3 5/8" |
| 12/12 | 45.00° | 1.414 | 1'-5" |
Rafter length = run × factor (before the ridge cut and overhang).
Concrete slab, 4" thick
| Slab | Cubic yards | 80 lb bags |
|---|---|---|
| 10×10 ft | 1.23 | 56 |
| 12×12 ft | 1.78 | 80 |
| 10×20 ft | 2.47 | 112 |
| 20×20 ft | 4.94 | 223 |
| 24×24 ft | 7.11 | 320 |
| 30×30 ft | 11.11 | 500 |
No waste added: order ~10% more. 80 lb bag = 0.6 ft³.
Rules of thumb
- Square a corner with 3-4-5 (or 6-8-10, 9-12-15): if the diagonal matches, it is 90°.
- First 16" O.C. mark at 15 1/4" from the end, so the sheet edge lands on stud center at 48".
- Board feet = thickness × width × length (all inches) ÷ 144.
- A 4×8 sheet covers 32 ft²; divide wall or floor area by 32, then add 10%.
- Header for a 2×4 wall: two 2× plus 1/2" plywood = 3 1/2", flush with the studs.
framersmath.com · free framing calculators · estimates only, check your local code
Calculators for each table
Studs for a wall (layout studs) · Stairs: risers for a total rise · Floor joist max span, No. 2 grade · Roof pitch · Concrete slab, 4" thick